Tesla has added a way for its Powerwall home-energy system to coordinate with compatible heat pumps, using cheap electricity or surplus solar power to increase stored heat before energy becomes more expensive. The new Heat Pump Optimization feature, reported in early November 2026, is initially available in Europe for suitable Powerwall 3 and three-phase Powerwall 3P systems.

That sounds like a useful combination for households with solar panels, a battery and an electric heating system. But how exactly does it work, which heat pumps are compatible, and can every Powerwall owner switch it on through an app?

What is Tesla Powerwall Heat Pump Optimization?

Heat Pump Optimization lets the Powerwall send operating signals to a compatible heat pump using information about solar generation, electricity prices and the homeowner’s chosen energy-management mode.

When additional solar electricity is available, the system can recommend that the heat pump increase its activity. Heat is then stored, typically by raising the temperature in a suitable hot-water or buffer tank.

The aim is to use electricity when it is available at lower cost and reduce the need to run the heat pump during less favourable periods.

The feature is part of Tesla’s home-energy controls, rather than a new battery chemistry or a claim that the Powerwall has gained extra electrical storage capacity.

How does the new feature work?

Tesla’s installation documentation describes two heat-pump operating signals:

  • Normal: The heat pump follows its ordinary thermostat and programming.
  • Boosted: The system asks the heat pump to increase operation and store extra thermal energy, subject to its own controls.

Powerwall provides the signal through a low-voltage, dry-contact relay connection to a compatible heat pump.

Importantly, the relay signal is a request to the heating equipment. The heat pump’s own controller, limits and configuration still determine how it responds.

This arrangement differs from directly sending power from the battery to the heat pump. It is a form of load scheduling: the timing of heating demand is adjusted so more electricity can be used when conditions are favourable.

What is SG-Ready, and why does it matter?

SG-Ready stands for Smart Grid Ready, a certification associated with the German Heat Pump Association, known as BWP.

Compatible heat pumps expose control contacts that allow an external energy-management device to indicate preferred operating conditions.

Tesla uses an SG2 contact to request the boosted mode. The installation documentation specifically distinguishes it from the SG1 contact associated with blocked or forced operating states.

That detail matters because a product described simply as a “heat pump” may not have the required SG-Ready interface.

Compatibility depends on the exact heat-pump model, available contacts, firmware, controller configuration and Powerwall system. A physical connection and commissioning are also required.

How does Powerwall decide when to boost heating?

According to Tesla’s documentation, the behaviour depends on the Powerwall operating mode selected by the homeowner.

In Self-Powered mode, the heat pump is asked to boost when excess solar electricity is available. When there is no surplus, it returns to normal operation.

In Savings mode, a boost can be requested when there is either surplus solar production or a low electricity price.

At medium and high electricity prices, the heat pump generally follows its ordinary settings.

This means the new feature may be useful both for households with midday solar production and for some customers whose electricity prices vary over time.

Savings are conditional on the energy tariff, heating demand, the size and efficiency of the thermal store and the heat pump’s response. No fixed percentage reduction in bills can be assumed for every installation.

Does this turn a hot-water tank into a battery?

In a limited sense, yes: a properly designed thermal store can hold energy as heat, although it is not an electrical battery.

For example, a tank can be heated to a higher temperature while solar production is abundant, allowing that stored heat to be used later.

The usable amount depends on the volume of water, the temperature change and thermal losses. Heat-pump efficiency also varies with operating conditions and the temperature the equipment must reach.

The advantage is the possibility of shifting some heating demand away from expensive hours. The trade-off is that storing heat at higher temperatures can have efficiency and comfort implications that need to be assessed for a specific heating system.

The Powerwall can coordinate this process, but the hot-water tank’s thermal storage capacity is separate from the Powerwall’s electrical storage capacity.

Which Powerwall owners can use the feature?

Tesla’s European rollout has been described for Powerwall 3 and Powerwall 3P with compatible heat-pump installations.

Reporting on the launch identified software prerequisites including Powerwall firmware 26.26 or later and Tesla app version 4.59.1 or later, in addition to a suitable SG-Ready heat pump and physical wiring.

The feature was initially described as Europe-only. As of early November 2026, Tesla had not announced an equivalent launch date for customers in the United States or Canada.

Regional availability may depend on installed hardware, local electrical standards and supported integrations. Owners should verify the exact requirements through Tesla’s current documentation and an appropriately qualified installer.

Can a homeowner enable it without changing wiring?

The integration normally requires a physical connection, not merely an app update.

Tesla’s documentation describes wiring a compatible heat pump’s SG2 input to the relevant low-voltage control terminals on a Powerwall or supported Backup Gateway, followed by configuration during commissioning in the Tesla One installer app.

This is specialist electrical work. Installers need to follow the equipment manufacturers’ instructions and applicable electrical safety requirements.

Another important limitation is that configuring Heat Pump Optimization can override an existing load-shedding configuration using the same control circuit. The two functions cannot always use that relay simultaneously.

A household that already relies on that output for backup-load management must consider this before enabling the new integration.

What happens during an outage or software update?

Tesla documents how the relevant control relay behaves when power to the controller is lost or the system is stopped. The low-voltage contact may open, returning the heat pump’s external request to its normal state.

That reflects a basic principle of the integration: the heat pump retains its own controls rather than relying exclusively on a Powerwall instruction to operate safely.

The feature should not be treated as a guarantee of continuous heating during a grid outage. Actual backup behaviour depends on the electrical design, power available and the heat pump’s requirements.

Does the feature make a Powerwall more economical?

It could improve the value of an existing home-energy system by making better use of cheap or self-generated electricity. But an individual assessment needs to compare installation costs, tariff structures, annual heating requirements and the heat pump’s actual performance.

For some homes, the additional heat stored during sunny hours may reduce electricity bought later at higher prices. For others, limited thermal storage, fixed tariffs or heat-pump control constraints may reduce the benefit.

It is also worth noting that SG-Ready load management existed before Tesla introduced this integration. The development is significant because it brings that capability into Tesla’s own Powerwall control ecosystem.

What is new about Tesla Powerwall in November 2026?

The key development is integrated heat-pump scheduling for compatible European Powerwall 3 systems, with normal and boosted requests informed by solar generation and, in Savings mode, electricity prices.

The feature requires supported hardware and a correctly configured SG-Ready connection. It does not amount to a universal software-only upgrade for all Powerwall owners or all heat pumps.

For people searching Tesla Powerwall updates in November 2026, the practical question is whether their particular home-energy installation has the equipment, wiring and tariff conditions needed to benefit from the new control feature.